2009 BMW 328I FUSE BOX LOCATION
Interior Fuse Box Location: 2006-2013 BMW 328i 2009 BMW
Some BMWs have multiple interior fuse boxes including in the trunk - the video above will show you where the interior fuse box of your 2009 328i is located. If your 328i has many options like a sunroof, navigation, heated seats, etc, the more fuses it has.
SOLVED: Fuse box on 328i bmw 2009 - Fixya
wwwa›Forum›Cars & TrucksFuse box on 328i bmw 2009 - Cars & Trucks. Posted by Anonymous on Jul 12, 2013. Want Answer 0. Where is 2007 bmw 328i fuse box location. On this website you find fuse box diagram and description for BMW 3 Series (2005 - 2010) BMW 3 Series E90 E91 E92 E93 2005 2010 fuse box diagram.Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US. Here's a link to this great service Good luck!you actually have a few different fuse locations. the main fuse box is located inside the glove box. open the glove box and look up. you should see 2 white tabs. twist them either clockwise or counter clockwise 1/4 turn panel should then be exposed. a sheet with the fuses and descriptions should be there to.0I have 1998 BMW 328i and it shut off entire air condition system while running. sometime it works fine then suddenly it shut off while driving.0Your sensor is going bad or you have to change your oil.01999 BMW 328I 2 EFI DOHC 6cyl Starter - Removal & Installation The
starter motor on some models is very difficult to see from the top of
engine compartment as it is covered by the intake manifold. On these
models, without removing the intake manifold, the starter motor must be
removed from underneath the vehicle. Because the starter motor mounting
bolts are not easy to access, a long extension with a universal joint
mounted on a proper sized socket could be used. A three foot
transmission extension is commercially available from tool vendors that
has a 3
inch drive of the driven end and
inch drive on the drive end. If used with a non-binding impact
universal joint and a proper fitting impact socket, the starter motor
fasteners can be removed from underneath the vehicle. Once the starter motor fasteners are removed, the
starter motor may have to be moved side-to-side several times to loosen
the dowel pin if it has corroded in place. NOTE When the battery is disconnected, the radio code, on-board
computer and clock settings will be lost. The radio code should be
obtained before disconnecting the battery or radio. Once the battery
has been reconnected, the radio will not function unless the code is
keyed in. Starter motor electrical terminal fastener torque specifications for all models: M5 terminal fasteners: 44 inch lbs. (5 Nm) M6 terminal fasteners: 53 inch lbs. (6 Nm) M8 terminal fasteners: 115 inch lbs. (13 Nm) Starter motor mounting fasteners: Hex head bolts: 36 ft. lbs. (49 Nm) Torx bolts: 32 ft. lbs. (43 Nm)
Starter motor electrical terminal fastener torque specifications for all models: M5 terminal fasteners: 44 inch lbs. (5 Nm) M6 terminal fasteners: 53 inch lbs. (6 Nm) M8 terminal fasteners: 115 inch lbs. (13 Nm)
Starter motor mounting fasteners: Hex head bolts: 36 ft. lbs. (49 Nm) Torx bolts: 32 ft. lbs. (43 Nm) E36 6-Cylinder Engines Automatic Transmission Models Before servicing the vehicle, refer to the Precautions section.
Set the ignition switch to the
Disconnect the negative battery cable. Remove the climate control air intake duct at the rear of the engine compartment as follows: Release the grille clips at the rear and lift the grille upward from the rubber seal, then remove the seal. Remove the two self tapping Phillips screws from inside the duct to release the electrical harness housing. Press the electrical housing downward to expose and remove the
two hex head self tapping screws on each side of the duct and lift the
duct up and out of the engine compartment. Remove the intake manifold trim and valve cover trim covers. Disconnect the ignition coil electrical connectors and ground straps, label for reinstallation and place aside. Remove the two fasteners that secure the fuel injection
electrical connector harness to the rail. Remove the harness and
carefully place aside toward the back of the engine compartment behind
the right side strut tower. Remove the intake manifold. Remove the electrical leads from the starter motor and place aside. Remove the starter motor mounting fasteners at the transmission
bell housing, then remove the two mounting nuts at the L-shaped
mounting bracket. Loosen the L-shaped bracket to engine block mounting bolt slightly, then remove the bolt while supporting the starter motor. Remove the bracket, then lift the starter motor upward away from the engine. Visually inspect the starter pinion and ring gears for any signs of damage. Installation is in reverse order of removal. Manual Transmission Models Before servicing the vehicle, refer to the Precautions section.
Set the ignition switch to the
Disconnect the negative battery cable. Raise and safely support the vehicle. Remove the fasteners for the reinforcement mounted between the
frame rails just behind the rear lower control arm bushing brackets.
Mark the bar-s direction for proper reinstallation and remove the bar. Remove the fuel line cover located near the left side rear lower control arm bushing bracket. Release the fuel lines and reverse light wiring from their routing brackets. Note the routing of the starter motor electrical wires, remove the wire mounting nuts, and place the wires aside. Remove the top and bottom starter motor to engine-transmission mounting fasteners. Remove the two mounting nuts at the L-shaped mounting bracket. Loosen the L-shaped bracket to engine block mounting bolt slightly, then remove the bolt while supporting the starter motor. Remove the bracket and carefully lower the starter motor downward away from the engine. Visually inspect the starter pinion and ring gears for any signs of damage. Installation is in reverse order of removal. Fig. A view of the starter motor mounting fasteners and dowel pin. The mounting bolts are threaded into the starter motor Fig. The starter motor mounting bolts are a different size than the transmission-to-engine mounting bolts I hope help you with this (rated this help) Good luck.0radio does not work on my 1997 bmw 328 it gives the message
"phone" a mechanic pulled it out of its slot and reset the code. worked for two days and again it doesnt work with same message0On this website you find fuse box diagram and description for BMW 3 - series (2005 - 2010) BMW 3 Series E90 E91 E92 E93 2005 2010 fuse box diagram Auto Genius0SOLVED: Where is 2007 bmw 328i fuse box location - FixyaSOLVED: Where is the fuse box on 328I bmw?See more results