2010 DODGE AVENGER UNDER HOOD FUSE BOX
Where is the fuse box for a 2010 dodge avenger located at
wwwers››Dodge›Dodge Vans›Dodge Grand CaravanAnswers ® Categories Cars & Vehicles American Cars Dodge Dodge Vans Dodge Grand Caravan Where is the fuse box for a 2010 dodge avenger located at under the hoodWhere is the Location of fuse box on 2008 dodge avenger?Mar 18, 2019Where are the fuses under the hood located on a 2000 dodgeMar 16, 2019Where is the fuse box on a dodge 2010 dodge avenger?Mar 09, 2019See more results
SOLVED: 2010 Dodge Avenger 2.4 l above the fuse box are
wwwa››Dodge›Avenger›2010 Dodge AvengerIs there more than the one fuse box other than the one under the hood of a 2010 dodge avenger? The only one listed in the owners manual is the one under the hood. Known as the Totally Integrated Power Module, it should be the only one.Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US. Here's a link to this great service Good luck!I'd get a 12vdc test light if you don't have one already & start from plug, and keep probing back from there. It may be as simple as a bad connection under truck where joined into harness.0I had the same problem, I found the post quoted below and fixed the problem in about 1 hour without having to replace any parts. Hope this helps!
(I can't seem to get back into the link but had copied the answer - the original link is: http://wwwboutauto/2007/_chevrolet_blazer_turn_signal_clicking_noise ) "I had this same problem and fixed it myself. The problem is caused by the contacts rubbing and releasing small particles which conduct small amounts of electricity and cause the flasher relay to click. From a GM Goodwrench mechanic. Disconnect Battery Before doing this. You need to remove the turn signal arm from the steering column. This may seem difficult but it really isn't. Separate the top and bottom covers. Find the screws and remove the switch. One is located behind the column and requires some dexterity to get out. I used a Torx bit on a 1/4 box wrench. The difficult part is separating the switch to clean the contacts. Take your time and you can figure out how to separate the switch. If I remember right, the switch separates and then the emergency signal switch slides out. Also, pay special attention to the way the rotary wiper delay switch is set into the switch. Once you can see the contacts, clean them off of all lubricant and metal pieces. I would hesitate to use Isopropyl Alcohol for this because off the plastics involved. I just used lots of Q-Tips and a lot of patience. Finally, get a good Dielectric (non-conducting) lubricant from auto store and cover all contacts with a thin layer. Put the switch back together, reinstall and test. This took me about four hours to repair. Because I took my time and did not force anything. Once I figured it out it wasn't that hard. The hard part was the rotary delay switch and how it was set into the switch. I figured if this didn't work, I was going to have to replace the switch anyway, so what the hell. Just make sure your local auto parts store has one of these available if you screw this one up. Did this about four years ago and problem has not returned since."0ASD relay faulty? Try swapping it with same number from other relays & see if clicking stops. I believe there is others same # in there, but might not be. Get back to me if not.0Try removing the battery terminals and clean both posts and terminals. Coat same with an anti-corrosion grease. Wash your hands after this to prevent mysterious holes in your clothes. Start the engine and measure the voltage at the battery terminals--should read 13.5 to 14.5 volts. Hope this helps.0I have seen once before that the fuse box was bad on a 2003 Dodge 3500. I had power in and nothing out. We had to replace the box. Not cheap! Hope it is simple like a loose connection though. I think I had to pull the inner fender on the drivers side to access the bottom of the fuse box. Pain in the ****, but..0Hello Jeffrey, it should be printed on the fuse box cover. From the "clicking" you describe, this sounds more like a relay than a fuse.0SOLVED: AVENGER FUSE BOX DIAGRAM - FixyaFuse box diagram for 2010 dodge avengerSee more results