LS2 WIRING HARNESS AND COMPUTER
LSA, LS9, LS2, LS3 Stand Alone Engine Harness For E67 ECU
Built From Scratch Stand Alone Engine Harness. An engine management harness is pretty much what you will find from most wiring harness companies. Basically, it contains all of the necessary functions to make the engine start and run, while also supplying any necessary signals from the computer such as speedometer and tachometer.
Standalone LS2 / LS3 Swap Wiring Harness | Drive by Cable
Brand new Standalone LS2 / LS3 swap (drive by cable) wiring harness. No cores or modifications needed. Made in USA with a start-up guarantee.
58x LS2, LS3, LS7 Stand Alone Engine Harness For E38 ECU
58x LS2, LS3, LS7 Stand Alone Engine Harness For E38 ECU $ 599 Please call for harness package with programmed computer and pedal $1095 There is no output wire for oil pressure or temperature gauges since the aftermarket usually supplies sending units and wiring for these. The harness will have provisions to plug in to the stock oil
Speartech | LS Harness | LT Harness | LSX Swap Harness
Speartech is your LS & LT wiring harness swap specialist. We offer LS / LT swap harnesses for all Gen 3, 4 and 5 LS / LT engines including LS1, LS2, LS3, LS6, LS7, LSA, LS9, Gen 5 V8, LT1, LT4 ,LQ4, LQ6, L99, Vortec variants - DOD, VVT, AFM. Speartech also provides ECM programming (including E38, E67, E40, E92), LS / LT engine wiring harness reworks and conversion, adapters, and programming
LS SWAPS: Wiring Harness and Wiring Guide
Mar 10, 2015This includes the computer, wiring harness, mass airflow sensor (MAF), oxygen sensors, and if the engine is drive-by-wire, the gas pedal and throttle actuator control (TAC) module. Each engine requires the use of its own specific computer and harness, and keep in mind that there were changes made to each system year by year.
Southern Performance Systems: Gen IV Wire Harness Kits
If you are building a Hot Rod - Muscle Car - Off Road Vehicle then our Plug-N-Play Packages is as easy as 1, 2, 3. All Wire Harnesses are tagged and come with instructions. All Custom Gen IV Wire Harnesses are professionally built to excede OEM standards. The harness shown on the page is an example of a LS3 with 4L70E setup.
LS SWAPS: Engine Management Systems Guide
Mar 09, 2015You can also convert an engine to drive-by-wire by reprogramming the original computer for drive-by-wire, but you must be able to plug the wiring harness into the particular computer. The 1998 F-Body computers and harnesses are not compatible with 1999-up harnesses or computers because the plugs are different.
LS Gen3 24x Standalone Harness – Swap Specialties
LS Gen3 24x Standalone Harness $ 495. Swap Specialties 24x Standalone wiring harness for GM Gen3 4.8, 5.3, 5.7, and 6 Engines have proven to be the best harness on the market today. We hand build every harness to fit exactly what your project needs and they actually form fit on the engine to make your wiring look and perform perfectly.
SSW | LS1 Wiring Harness and Tuning | LS1 wiring
LS1 Wiring Harness and Tuning, Standalone LSX Harness The SSW LS1 wiring harness, as well as the LS6, LR4, LM7,LQ4, LSX wiring is based on the General Motors 411 electronic control module. The SSW LS1 electrical wiring harness has full diagnostic capabilities, and a 4L60E controller. The Ls1 wiring harness consists of all connectors 
Related searches for ls2 wiring harness and computer
ls2 wiring harness instructionsls2 wiring harness conversionls2 swap wiring harness2005 ls2 engine wiring harnessls2 stand alone wiring harnessls3 engine wiring harnessls3 wiring harness kitgm ls3 wiring harness