VDO DIGITAL SPEEDOMETER WIRING DIAGRAM
Speedometer 1 2. Lamp Socket (Push in, wedge-type) 2 3. Light Bulb (12-volt / G.E. #158 or equivalent) 2 4. VDO Spin-Lok™ Mounting Clamp 1 5. Installation/Operation Instructions 1[PDF]
Programmable Speedometer (3 1/8" or 3 3/8" diameter) 1 2. Voltmeter (21/16" diameter 1 ment refer to Table 1 and Diagram C. IIure the tank depth of your fuel tank. Locate this dimension Wrap excessive lead wire around bracket 'g' and re-install with nut and washer.
Speedometer - VDO Gauges
ViewLine Ivory 120mph 3 3/8" (85mm) Electronic Speedometer with Warning Lights & Autocalibration 12/24V[PDF]
0 515 012 123 -- Electric Gauges - VDO Instruments
VDO Spin-Lok™ Clamp or mounting bracket 1 5. Installation Instructions 1 CAUTION: Read these instructions thoroughly before making installation. Do not deviate from assembly or wiring instructions. Always disconnect battery ground before making any electrical connections. If in doubt, please contact 0 515 012 123 -- Electric Gauges[PDF]
ELECTRONIC SPEEDOMETER HALL EFFECT SENDER
ELECTRONIC SPEEDOMETER HALL EFFECT SENDER INSTALLATION INSTRUCTIONS AND WIRING DIAGRAM 7UDQVPLVVLRQ TYPE A SPEEDOMETER (#1) position. Install and wire the speedometer as shown earlier. 2. Drive a known course with a distance of up to 10 miles. Be sure the speedometer[PDF]
Siemens VDO CAUTION!!! Tools and Materials Needed For
junction, and attach the wire from the speedometer. Refer to Diagram D for the proper wiring of the speedometer. 3. Attach the wire from pin #3 to a ground (negative) source. One such source can always be found where the battery is attached to the metal frame of the vehicle. Use an appro-priate electrical connector to ground this wire. 4a.
Gauge Wiring Diagrams
Digital Displays . All-in-One digital display system. The DigiDash 2 LITE is for road and track day use. Sensors for VDO Gauges . 80 & 100mm Electronic Speedometer Mk3 - General Wiring Diagram & Instructions, Hall-effect M8 sensor (340 002) + Magnetic Induction Sensors: 433kb:
Tachometer Installation and before cutting any holes
assembly or wiring instructions. Always disconnect the battery ground before making any electrical connections. Diagram A VDO Tachometer with Hourmeter is programmable from .5 to 200 pulses per revolution VDO VDO Item Description Quantity 1. Tachometer 1 2. Lamp Socket (Push in, wedge-type) 2 3. Light Bulb (12-volt / G.E. #161 or equivalent) 2 4.
VDO Installation and Troubleshooting Guides
Note: These Instructions are for VDO Gauges and Accessories only. Click here for Auto Meter, Classic Instruments, Defi or ISSPRO Instructions. Please note that if you have a problem opening the PDF files just by clicking on the link, please right click your mouse button over the file name and select "Save Target as" to your Desktop.[PDF]
ELECTRIC SPEEDOMETER Recommended – Auto Meter Hall effect sender, 3-wire 16 pulses/revolution. Standard 7/8 – 18 thread 5292 Ford, plug in GPS Interface Module Universal Speed Sensor 3299 Optional Tach/Speedo Gauge Connector Calibration (Electric Speedometer calibration made easy!) To calibrate your electric speedometer: 1.
Related searches for vdo digital speedometer wiring diagram
vdo speedometer wiring diagramvdo electronic speedometer wiringvdo speedometer schematicvdo gauge wiring diagramvdo clock wiring diagramelectronic speedometer wiring diagramvdo gauge wiring harness diagramvdo speedometer installation instructions