WIRING DIAGRAMS XBEE TEMPERATURE
Wiring | XBee Radios | Adafruit Learning System
CTS - "Clear to Send" this is a flow control pin that can be used to determine if there is data in the XBee input buffer ready to be read. 5V - this is the power input pin into the 3 regulator. Provide up to 6V that will be linearly converted into 3. RX - This is the XBee's serial recieve pin.
XBee - Wiring
/** * Simple xBee comunication example * by Jaime Patarroyo * * communicates two Wiring boards using xBee's modules, * pressing the button attached to one Wiring, will * light the board LED (48 for Wiring 1.0 boards, pin * 15 for Wiring S) on the other board.
DS18B20 Bluetooth Thermometer – Circuit Wiring Diagrams
At the heart of the board is a PIC12F675 microcontroller in an SO8 package. The right-hand side of the board houses the linear power supply (LP2950), bottom-center is the DS18B20 1-Wire temperature sensor, and out in left-field you can see the Sure TTL Bluetooth Module.
Temperature Controller Wiring Diagram | Free Wiring Diagram
Temperature Controller Wiring Diagram - Collections Of Wiring Diagram Controller List Trusted Wiring Diagrams •. Wiring Diagram Controller List Trusted Wiring Diagrams •. Wiring Diagram Controller List Trusted Wiring Diagrams •. Motor Control Wiring Diagram Symbols Elegant Circuit Diagram.
How to Wire a Temperature Gauge | It Still Runs
Engine temperature directly affects combustion and moving internal parts. Without a temperature gauge, the engine would be subject to various modes of heat without the operator's knowledge, and this could lead to bearing failure and engine seizure. A vehicle owner can wire a temperature gauge in his or her vehicle in a driveway or garage.
Building a wireless temperature sensor with a Raspberry Pi
Jun 13, 2014Here are the parts you will need for this project: (2) XBee Series1 Wireless Units. (1) XBee Explorer USB Board. (1) TMP36 Analog Temperature Sensor. (1) XBee Breakout Board. (1) Raspberry Pi Model B. Jumper Wire, Breadboards, USB [PDF]
XBee™/XBee-PRO™ OEM RF Modules
Mechanical drawings of the XBee/XBee‐PRO OEM RF Modules (antenna options not shown) The XBee and XBee‐PRO RF Modules are pin‐for‐pin compatible. 1.4. Mounting Considerations The XBee/XBee-PRO RF Module was designed to mount into a receptacle (socket) and therefore does not require any soldering when mounting it to a board.[PDF]
XBee /XBee-PRO RF Modules - sparkfun
The XBee®/XBee-PRO® RF Module was designed to mount into a receptacle (socket) and there-fore does not require any soldering when mounting it to a board. The XBee Development Kits con-tain RS-232 and USB interface boards which use two 20-pin receptacles to receive modules. Figure 1‐02. XBee Module Mounting to an RS‐232 Interface Board.
Measurement Circuits – Page 3 – Circuit Wiring Diagrams
– Connect the boards: solder wires according to the hardware schematics and wiring diagrams. Note that XBee Chip Antenna modules should not be soldered: they fit into the XBee Explorer Regulated socket. 2.1.2. Transmitter Config – Put an XBEE module on the RECEIVER socket and plug the USB cable into the PC.
Arduino 1-Wire Tutorial - hacktronics
All of the DS18B20 temperature sensors can be connected to the same IO pin: * You only need one 4 pullup resistor for all 1-Wire devices connected to Arduino pin 3. ** See the DS18B20 datasheet for the pin diagram, and be very careful. Wiring this part backwards will fry it!