WIRING HARNESS FIERO 3 4 DOHC
3.4 DOHC wiring harness - Pennock's Fiero Forum
Aug 14, 2018Pennock's Fiero Forum The Mall 3.4 DOHC wiring harness 3.4 DOHC wiring harness. Post Reply Email This Page to Someone! Goto: 3.4 DOHC wiring harness by Sietetx. Started on: 08-14-2018 12:24 PM: Replies: 0 (87 views) Last post by: Sietetx on 08-14-2018 12:24 PM: Aug 14th, 2018. Sietetx Member . Posts: 244 From: Nowhere Kansas Registered: SepIs a 3.4 DOHC hard to drop in a 86, 4 speedDec 02, 20193.4 DOHC swap - Pennock's Fiero ForumJul 16, 2016Sourmug's 3.4 DOHC SwapJul 26, 2011Pennock's Fiero ForumJul 04, 2006See more results
3.4 DOHC Fiero Swap -- page 1
3 DOHC Fiero Engine Swap Guide. page 1. To simplify this swap guide, I have taken excerpts of the swap thread I documented over on Pennock's Fiero Forum. You can access that thread here. If that thread gets archived, you can search the archives on PFF for the title: Project 3.4 TDC / 4-speed muncie swap underway..
3.4 DOHC Fiero Swap -- page 6 - Sinister Performance
3 DOHC Fiero Engine Swap Guide. page 6 . At this point you can elect to do continue on several different ways. I decided to get on the A/C and wiring. For the A/C system, I used the A/C compressor from a 94-up 3 DOHC engine which was R134a compliant.
3.4 DOHC Swap OBDII or OBDI? - Pennock's Fiero Forum
Nov 02, 2017All; I am finally at the point where I am installing my 3.4 DOHC swap that has been sitting for way too many years. A bit of background. I bought a '95 DOHC off a fellow Calgary Fiero owner and commissioned Erik from here to make me a 3.4 DOHC harness.
A 3.4 DOHC Build then.. F40 Turbo - Pennock's Fiero Forum
Feb 14, 2013The 3.4 DOHC Swap begins. I got bored with the pushrod 3.4 and due to a couple issues, I decided it was time to swap it out. My goal for this swap was to do a complete 94-95 3.4 DOHC swap with factory style routed exhaust, using my cars original (216,000 mile) 282 Getrag. The engine management system was on the 94-95 OBD 1.5 platform.
3.4 engine conversion kit - Pennock's Fiero Forum
Dec 15, 2014The 3.4 will utilize the fiero's motor mounts, flywheel, clutch, wiring harness, and all other accessories. The only adaptation that will need to be made is relocating the starter on the 3.4 to match the starter location on the 2.8, which only requires drilling a few holes. This swap is about as close to plug-and-play as you can get.
3.4 DOHC Fiero Swap -- page 2 - Sinister Performance
IN my case, the stock 2.8 pump was in bad shape so I replaced it with a unit made for a 92 Chevy Lumina 3 DOHC. I bought a new fuel pump from AutoZone which came with a wiring kit so it would interface with the 86 Fiero's older in-tank wiring harness.
Related searches for wiring harness fiero 3 4 dohc
fiero wiring harnessfiero wiring diagram