WIRING LIGHT SOCKETS TOGETHER
How to Wire-up a Light Bulb-socket Items.The First Thing You Need to Do Is,Slide It Out.Striping the Wires.Sliding the Wires Through... (more items)
How to Wire-up a Light Bulb-socket: 10 Steps
Is this answer helpful?Thanks!Give more feedbackThanks!How can it be improved?How can the answer be improved?Tell us howPeople also askHow to wire lamp socket?How to wire lamp socket?Wiring the Socket Unscrew the cap from the socket and string the cap onto the lamp cord.If your cord has a cloth covering,expose a few inches of the insulated cord within.Insert one of the wires into the appropriate slot of the wire strippers.Divide the neutral wires in half and twist both halves into tight strands.For the Makers: How to Wire a Pendant LampSee all results for this questionHow to rewire a table lamp switch?How to rewire a table lamp switch?How to Rewire a Lamp Try the Old Cord to the New.Feed the New Cord.Disconnect the Wires.Rewire the Socket.Connect the Socket Wires to the Lamp Cord.How to Rewire a Lamp | how-tos | DIYSee all results for this questionHow to wire-up a light bulb-socket?How to wire-up a light bulb-socket?2:24Lamp Socket WiringSee all results for this questionHow to rewire a lamp?How to rewire a lamp?7:10How to Rewire a Lamp - Replace a Lamp SocketSee all results for this question
electrical - How to connect multiple light fixtures to one
How to connect multiple light fixtures to one switch? connect the other terminal on the switch to the black wire of the cable leaving this junction box towards the first light. The ground wire should also be connected together in this manner, but to the ground terminal on the switch. the switch) and "exiting" (away from the switch). AtBasically, you want to start with a switch. You run a black and white wire in from the bottom of the switch box (from the panel). This will take the form of 12/2 or 14/2 cable. You run another 12/2 or 14/2 cable from the top of the switch box to the first light. You connect the black wire to the switch. You connect the 2 white wires together, and then connect the other terminal on the switch to the black wire of the cable leaving this junction box towards the first light. The ground wire should also be connected together in this manner, but to the ground terminal on the switch. Each light will have a cable "entering" (from the switch) and "exiting" (away from the switch). At each light you'll connect the entering and exiting black wires together, as well as 1 terminal on the light. Do the same with the white wires. If there is a ground terminal on the light, do that as well, otherwise just connect the incoming and outgoing ground wires together. At the last light, just connect the incoming black wire to 1 terminal on the light, and then connect the white wire to the other one. This method is called wiring in parallel, so if one light blows, the current can still continue to the other lights to light them up. Some other things to be aware of: Most home wiring is either 12 or 14 gauge, corresponding to either a 20 amp or a 15 amp circuit, respectively. The maximum "design capacity" is 80% of that. Let's say you're using a 20 amp breaker with 12 gauge wire. This circuit should run at no more than 16 amps. Let's assume you're using 100 watt bulbs at 120 volts. Using watts/volts = amps, for 600 watts/120 volts = 5 amps. So this would work fine on a 15 amp breaker, depending on what else is on that circuit. http://wwwircuitdetective/ is also a superb reference for novice electricians to get an idea of how things work. Something like this is what you're looking for the end result to be:14Instead of needing to do electrical work there are power strips that have a wireless remote controls. Belkin creates the product and they are sold at Office Depot or Staples. Belkin Description: Control Standby Power to Your Whole Electronic Systems.
Now you can
control power to your whole electronic systems with a single click.
The Conserve Switch AV Surge Protector with Remote lets you shut off
power—including standby power—to all your entertainment electronics
with one touch of the wireless remote switch. One-Click Control.
The wireless remote controls six Remote-Switched
outlets for all your entertainment components—your TV, DVD player,
VCR, gaming console and more. Two Always-On outlets stay on for
devices that need continuous power, like your DVR. Place the remote on
a table or shelf, or mount it on the wall, for the convenient way to
save energy.0As a beginner myself, using a book, an electrician friend for advice, great caution and 1/2 brain, I wired a complete panel in my home, added garage lighting and several other circuits for appliances. I saved myself thousands of $ at the rate of $80-90 per hr electricians in our area. Electricians went through much training and OJT in order to become licensed. But like anyone in a trade that took much training, we often feel self inflated and feel that no one else can or should do our work unless they go through the same. But the bottom line is, if its your home electrify away and don't worry about possessive electricians. Just do it safely in order to protect yourself, family, others and property. For the simple stuff like wiring a planel and adding circuits for switches/outlets its a breeze. Save yourself much money if your state allows you to do it on your own.Power to a light, through two lights and then to a switchApr 15, 2017electrical - How do I wire two lights with a switchJan 11, 2013See more results
How to Wire a Lamp with Two Bulb Sockets | Hunker
How to Wire a Lamp with Two Bulb Sockets By Bryan Trandem | December 21, 2017 by twisting the bare ends together and screwing a wire nut over the bare ends. Do the same with the hot wires (this is the portion of the cord that has smooth insulation). Test, then reassemble the lamp: Reassemble the light bulb sockets inside their outer